Hello I was searching through the posts and Dialog stated:
“您不需要任何额外的电缆或JTAG，因为您拥有界面板，电路板有一个调试器，只需插入USB电缆即可打开它，您应该能够步进并运行IoT
fw with keil, you dont need anything extra. The interface you indicate in the picture is another interface in order to program reference designs with different Jtag connection plugs."
我有接口板/物联网传感器组合。我尝试通过智能片段下载代码，但并未成功，然后我注意到这篇文章。我想使用调试器
that is mentioned here but when I boot keil and compile the IOT project and try to open the debugger I get the error: No Cortex-M Device Found. My Keil works fine with the DA14580 development kit. Any ideas? Thank you. Craig
设备：
Hi Craig,
带有物联网传感器的接口板是在图5中的UM-B-063传感器开发套件文档中所示的接口板。请打开Keil并选择目标选项，转到“调试”选项卡，然后单击“设置”，在那里，您应该请参阅JTAG的SN（确保端口设置为SW而不是JTAG）。问题是，如果583内部闪光灯和FW实现睡眠中的固件，则JTAG无法连接到处理器。因此，如果您在SW设备文本框下看到处理器，请点击“确定”或“取消”按钮返回“调试”选项卡，在接口板上点击“重置”，然后再次单击“583睡眠”之前的设置选项，然后再次单击为了确保Keil能够与您的处理器通信。现在为了在击中KEIL上的调试按钮之前编程通杆，请点击接口板上的RESET按钮，然后在近似at 2秒内从KEIL命中调试按钮。我提醒您，上述功能是必要的，因为FW实现睡眠，调试器无法附加到580.您可以通过使用Smart Scompets和Connect通过JTAG来删除编程到Flash中的FW，然后点击闪存选项，点击闪存选项，点击连接，然后擦除，这样您每次想要编写您的电路板时都必须按住重置按钮。
Thanks MT_dialog
Thank you for the detailed response. That will help a number of people who will encounter this issue. As for me, I am still having troubles with my current board, I cannot program it with Smart Snippets or program it through Keil- I believe it is the board itself so I sent for a new one from Mouser and will recontact you if
I encounter any problems with that board. Many thanks again. Craig
Hi,
How much current will be drawn by "IoT Sensor Development Kit - 9 axis + Temp/Pressure/humidity" while sampling all sensors at high frequency.
Is any document regarding the current/power consumption details.
问候，
Mahesh Chandana.
嗨mahesh，
您可以在第12.1节中找到UM-B-063_DA145_IOT_SENSOR_DEVELIMENT_KIT.pdf的功耗测量。电源测量以及测量完成的传感器的速率。这些是在物联网上执行的可用测量
Thanks MT_dialog
您好，我正在遇到困难编程我的新董事会。电路板刚刚制造，并具有相同的引脚/引脚进行编程
（包括10个引脚标题）作为您的DA14583 IOT板。我无法使用UART / SPI模式或JTAG模式进行编程。我现有的
IOT sensor from Dialog programs fine in both of those modes. I think I really need support as these boards were very expensive to have
fabricated and there seems to be a hardware issue on them. The following errors were obtained from Smart Snippets: I am looking for
a strategy to debug them at this point. Thank you. Craig
JTAG MODE:
[信息@ 16-12-25 14:00:27]报头记录已从十六进制文件WRBL_SFL_583.HEX中删除。
[信息@ 16-12-25 14:00:27]从文件wrbl_sfl_583.hex中读取32688字节。
[INFO @16-12-25 14:00:28] Core is locked-up, trying to disable WDT.
[WARNING @16-12-25 14:00:29] Could not set S_RESET_ST
[WARNING @16-12-25 14:00:29] CPU did not halt after reset.
[WARNING @16-12-25 14:00:29] CPU could not be halted
[info @ 16-12-25 14:00:29]核心重置后没有停止，尝试禁用WDT。
[WARNING @16-12-25 14:00:29] CPU did not halt after reset.
[WARNING @16-12-25 14:00:29] CPU could not be halted
[WARNING @16-12-25 14:00:29] Could not set S_RESET_ST
[INFO @16-12-25 14:00:29] SYSRESETREQ has confused core. Trying to reconnect and use VECTRESET.
[警告@ 16-12-25 14:00:30]无法重置CPU。Vectreeset有困惑的核心。
[WARNING @16-12-25 14:00:30] CPU did not halt after reset.
[警告@ 16-12-25 14:00:30] CPU无法停止
[INFO @16-12-25 14:00:30] Core did not halt after reset, trying to disable WDT.
[WARNING @16-12-25 14:00:30] CPU did not halt after reset.
[警告@ 16-12-25 14:00:30] CPU无法停止
[警告@ 16-12-25 14:00:30]无法设置s_reset_st
[错误@ 16-12-25 14:00:30]在地址50000012处写入值A7失败。
[信息@ 16-12-25 14:00:30]将固件文件下载到电路板上失败。
[信息@ 16-12-25 14:00:30]配置SPI闪存端口和引脚。
UART / SPI模式：
[INFO @16-12-25 14:55:30] Header records have been removed from hex file wrbl_sfl_583.hex.
[信息@ 16-12-25 14:55:30]从文件wrbl_sfl_583.hex读取32688字节。
[INFO @16-12-25 14:55:35] Failed downloading firmware file to the board.
[信息@ 16-12-25 14:55:35]配置SPI闪存端口和引脚。
[INFO @16-12-25 14:55:44] Failed downloading firmware file to the board.
[信息@ 16-12-25 14:55:44]配置SPI闪存端口和引脚。
[信息@ 16-12-25 14:55:57]将固件文件下载到电路板上失败。
[INFO @16-12-25 14:55:57] Failed configuring SPI Flash ports and pins.
[信息@ 16-12-25 14:56:13]将固件文件下载到电路板上失败。
[INFO @16-12-25 14:56:13] Failed configuring SPI Flash ports and pins.
[信息@ 16-12-25 14:56:17]将固件文件下载到电路板上失败。
[信息@ 16-12-25 14:56:17]配置SPI闪存端口和引脚失败。
[INFO @16-12-25 14:56:28] Failed downloading firmware file to the board.
(信息@16-12-25 14:56:28]失败配置SPI Flash ports and pins.
Hi Craig,
关于FLASH编程，请检查电路板设置中的SPI闪存引脚配置以匹配DA14583引脚辅验，并在没有电流测量功能时使用UART / SPI模式而使用UART / SPI模式。SmartSnippet通常要求用户按UART模式按RESET按钮，以便在编程闪存图像之前下载Flash_Programmer.bin，但我在您提供的控制台中没有看到它。因此，您的设置可能会有一些不正确的步骤。还请确认两个UART和JLink驱动程序已正确安装。
keil不支持Flash下载。请使用“调试”并将图像下载到RAM。
谢谢莫里斯
谢谢你的帮助。我意识到我错过了40VFQFN处理器的中央焊盘。路由
some lines underneath the pad. I think this is the issue. I looked at the datasheet and there is not much
mention of the central pad and I was unaware of this need this being my first time using this chip
format.
为了解决我的修复，我必须在处理中央地板上有点创造力，我需要知道（并且不能
在数据表中找到），如果引脚16（DA14583 GND引脚16）内部连接到中央地板？如果没有，我可以逃脱没有接地
那个中央地板或绝对必要性吗？先感谢您。克雷格
Hi Craig,
The pin 16 is the DCDC ground and is not connected to the substrate ground which is the central ground pad. So it is necessary to have ground pad connection. The layout of evaluation board may provide you a good reference.
谢谢莫里斯