I have prototype boards containing the DA9053 PMIC and would like to know the requirements for connecting the Power Commander running on a PC to the PMIC, which in my case needs to use the 2-wire I2C interface. I see there is documentation for doing this to your eval boards, but cannot find an explanation for doing it on a production board. Thank you.
Device:
Hello Jeremye,
You will need access to Vsys, GND, GPIO14, GPIO15 and TP on your prototype board. TP will need to be pulled-up to VDDCORE. GPIO14 and GPIO15 will be your I2C pins.
Whilst you can get the DA9053 to enter Powercommander mode in system, you will not be able to program the part, this why we do not have any documentation on this.
I have a few questions:
Kind regards,
Elliott Dexter
部分是DA9053-60HA2。我们之前没有使用过这种变体。它是标准变体，不被我们编程。
We don't have an eval board., and didn't have intention of using one to communicate with the DA9053 (that might change).
Your final question implies that I might use an eval board to communicate with the soldered-in part, is that the case? I had assumed I would need at least a USB to I2C bridge device.
The reason I want to do this is solely for debugging, not programming. For some reason the DA9053 will not communicate to the host processor on our board, over the 2-wire i/f) and I was hoping to find out what state it is in.
不幸的是,TP DA9053是connecte销d to 0V, and I don't think I can change that. Useful to know for future designs nonetheless.
Hello Jeremye,
I have used our ICP board in the past to force one of the DA9061/62/63 parts into Powercommander mode, I found this method easier for myself. However these parts are different. The -60 varaint has no AutoBoot, so you should be able to connected onto the I2C lines (GPIO14 and GPIO15) and have some element of control before the start-up and after start-up. However if you want to make changes before the start-up, you will have to make sure there are no IRQ's or wake-up events before you make the changes.
It will not be full powercommander mode, but its the best option we have.
Are you just testing the turn on of LDO4?
Kind regards,
Elliott Dexter
HI Elliott
That sounds encouraging.
我现在有点困惑我需要与DA9053沟通：ICP板，eval板或自定义界面？
Can you tell me what I need and how to obtain it? The Dialog website seems not very clear on this.
No, not trying to turn on LDO4 at present. I'd have to go down the route of custom OTP to make that viable, as It would need to turn on first in the sequence.
Thank you
Hello Jeremye,
Ok, So the ICP board is for the DA9061/62 and DA9063 only. This board is used for in-circuit programming only.
The two options you have is:
我将与应用团队快速交谈，看看是否有另一种可能性，但我认为我们只有两个选项。
Kind regards,
Elliott Dexter
My original problem was that the host processor couldn't communicate with the DA9053-60HA2 over the 2-wire Power Commander interface. Taking your earlier hint to use GPIO_14,15, I lashed-up an extra I2C connection to these pins and succeeded in getting the two to talk, Hurrah.
I've examined all the register state in the DA9053 and discovered a few unexpected things:
* The DA9053's PC I2C addresses (OxB0 write, 0xB1 read) have changed relative to the previous DA9053-3FHA2 variant we were using (Ox90 write, 0x91 read) .
*默认电源指令界面从2线更改为4线，我们的当前板无法处理。
The new I2C address is in contradiction to the DA9053's datasheet (v2.1, section 10.3, page 65), you might like to know.
To correct these issues, and a number of other minor issues, it's looking like the best way to proceed is to produce our own custom OTP data. Not having done that before, I wonder if you would give a pointer on how to get started with that? Thank you
Hello Jeremye,
The -60 and the -3F standard variants are for different processors. The -3F is for the i.MX53 and the -60 is for the i.MX6DL.
Kind regards,
Elliott Dexter