Hello, I am continuing to have problems with Smart Snippets. At one point Smart Snippets just refused to boot properly so I installed
a newer version, then an older version and now I am back to the newest version. There are no apparent problems until I get into the
programming screen. When I select the program button I get the following errors: The odd thing to me is that I states it has started the
download procedure but at this point I have only hit the connect button. I am using the IOT sensor piggybacked on the IOT development
board and the code is compiled under 5.160.1 which is the code and development system provided by Dialog for the IOT device. Hitting
the reset button on the IOT development board does not help.
The odd thing is that it was working perfectly then one day just stopped working and now I cannot get it to download software at all.
Thank you. Craig
[INFO General @17-10-04 17:02:07] Could not measure total IR len. TDO is constant high.
[INFO General @17-10-04 17:02:07] Could not measure total IR len. TDO is constant high.
[INFO General @17-10-04 17:02:07] Found SWD-DP with ID 0x0BB11477
[INFO General @17-10-04 17:02:07] FPUnit: 4 code (BP) slots and 0 literal slots
[INFO General @17-10-04 17:02:07] Found Cortex-M0 r0p0, Little endian.
(信息一般@17-10-04 17:02:07]BTLE device selected.
[INFO SPI Flash @17-10-04 17:02:28] Header records have been removed from hex file wrbl_sfl_583.hex.
[INFO SPI Flash @17-10-04 17:02:28] Read 32548 bytes from file wrbl_sfl_583.hex.
[INFO SPI Flash @17-10-04 17:02:32] Firmware File D:\DiaSemi\SmartSnippetsStudio\Toolbox\common_resources\flash_programmer.bin has been selected for downloading.
[INFO SPI Flash @17-10-04 17:02:32] Connection to COM5 port has successfully opened.
[INFO SPI Flash @17-10-04 17:02:32] Started download procedure...
[ERROR SPI Flash @17-10-04 17:02:56] CRC does not match.
[ACTION SPI Flash @17-10-04 17:02:56] Please click the Connect/Download button in SmartSnippets Toolbox and press the hardware reset button on the board to start the download process.
[INFO Booter @17-10-04 17:02:56] Successfully disconnected from port COM5.
[ERROR SPI Flash @17-10-04 17:02:56] Failed downloading firmware file to the board.
[ERROR SPI Flash @17-10-04 17:02:56] Failed configuring SPI Flash ports and pins.
Hi Graig flanaga,
Please check your pin configuration(uart/spi or jtag) and put a jumper to j16.
BR,
STS_Dialog.
Hello the pin configuration is correct on my system. I am thinking perhaps the development board is gone but not sure. Attached is the picture
of the programming screen. I did hit the reset button as well. Thanks. Craig
Hi,
Try it via jtag and check if it can scan the cpu through Keil. At option for target icon press it, then select the debug tab,at the right bottom of the window there are the settings of debugger press it and then press scan(if it's not find with the first attemp try to do hardware reset-from the button and immidiately press scan).
Thanks,
STS_Dialog
Hello
I am trying to install the software SmartSnippes but to intrepid run it I get the following message:
The Java Runtime Environment (JRE) or Java Development Kit (JDK) must be available in order to run SmartSnippes_Studio. In Java virtual machine was found after searching the following locations:
jre_bin_full_path in your current PATH
any idea how to solve this?
i can solve my problem simply in the file SmartSnippets_Studio.ini is found in C: \ DiaSemi \ SmartSnippetsStudio \ CDT \
replace the instruction jre_bin_full_path
by
-vm
C: \ DiaSemi \ SmartSnippetsStudio \ CDT \ jre \ bin