Hi,
Im trying to debug the keil projects from SDK5.0.4. I see an error for all the projects.
*** error 122, line 17: AGDI: memory read failed (0x000000C8)
请有人告诉我解决方案。谢谢你。
Hi,
I was working with PAN1740. I was using sps_device project. I was able to send and receive data to DSPS app in android.
Now Im looking to have communication between Bluetooth and PC. Do we have any project to achieve this ?. Thank you.
您好：
想使用命令行进行da14580外挂flash的烧写，却发现无法擦除flash
1、运行SmartSnippets.exe -type booter -chip DA14580-01 -jtag xxxxxxxx -file F:\project\smartsnippertsworkspace\resources\jtag_programmer.bin
运行后提示Successfully downloaded firmware file to the board.
2,运行SmartSnippets.exe类型spi芯片DA14580-01 -jtag xxxxxxxx -cmd erase
运行结束后提示SPI Memory erasing failed 擦除失败
利用smart snippets点击connect，再运行SmartSnippets.exe -type spi -chip DA14580-01 -jtag xxxxxxxx -cmd erase
会提示SPI Memory erasing completed successfully.擦除成功
SMART Scippet版本V3.6
Hi dialog，我目前有下載DA1458x_DSPS專案原始碼，想知道如何利用DSPS範例測試observer模式下的scan功能，謝謝!
Hi Team,
We want to download the "prod_test_580.hex" file on our custom Matherboard for Direct test mode validation. We are using the Smart Snippets tool and RF mster section . When I download the hex file,its said the error, "Timeout: Reset signal not detected for more than 15000 msecs."
we are using BLE_UART_TX and BLE_UART_Rx on P0_5,P0_4 pin and E3 Reset of Da14580(on board DA)
But this reset is not deteced on RF master.
Error:
Hi,
I try to program the SLG46826 chip in circuit with microcontroller. The SLG46826 chip has not programed with the factory I2C address 0x08.
但是，在我删除像页面0xc0这样的页面之后（页面可用于更改I2C地址设置），芯片锁定了所有寄存器值夹焦到0xFF（包括页面0xe0）。
The attached file shown the action I did and the response from the chip:
1. Read from page 0xc0, value are normal (I2C address 0x08)
2. Erase page 0xc0
3. Reset chip
Hi,
I found a wird situation (maybe using OSC0 wrongly). After some amount of time (~1h) the WDT driven by OSC0 stops working - as there is some timeout.
Conditions:
- WD_IN输入信号是外部识别[PIN13]
- 12V_MONITOR_IN signal is always presented [pin18]
谢谢你的帮助。
I am testing the DA7218 reference board with great success. The audio input and tone generator are both working well, at least from the input to the headphone output. However, I am unable to get any data out of the I2S port. I have configured this port in I2S and TDM, but the Data-out never toggles. The register setting file is attached. No doubt it's something very simple that I have set wrong. Any guidance would be appreciated.
谢谢-
Mike Schell
Hello,
I was wondering where I can find more information about the "Angle-of-Arrival demo on Dialog SmartBond™ Bluetooth® LE" device found on YouTube:
https://www.youtube.com/watch?v=jSDtUOQXJmo
预期发布日期是多少？
Thank you,
Stefano
I'm trying to program some DA9061s with the motherboard 232-01-B and socket board 232-02-A.
Previously I had success in both using power commander mode to test features and the ICP application to program chips, but now I can't do either. Maybe I'm missing something but it doesn't seem to be able to detect the DA9061. I've tried fresh parts and ones that have previously been OTP burned, and I've also tested the burned parts work outside of the motherboard.
Is there anything else I can look at?
