Interface DA14585 with a gyroscope
Hi
I want to use a gyro sensor to interface it with DA14585. I want to use I2C communication.Can I get some reference example for loading the code into the module
Regards,
Goutham.N
DA9063 Which part to order?
Hi Dialog,
I was wondering about ordering parts. Where can I get them (I need only 10-15 parts for my first prototypes)? How do I get a part with my required startup values for the LDOs and DCDCs?
Thanks!
Earl
DA9063 Not using the RTC
Hi Dialog, I want to use the DA9063 in my design. I was wondering about the xtal and RTC. I have no intention to use the RTC. I was wondering if I can just remove the XTAL. If so, what should I do with the pins? Also, will the switching frequency of the DCDCs be affected?
Thanks!
Earl
睡眠模式下100us GPIO中断无法唤醒MCU
我将MCU设置为睡眠模式后，外设产生的100us中断，通过GPIO未能正常唤醒MCU，请问这个问题的原因可能在什么地方呢？谢谢！
Wrong output SmartSnippets
Hello!
I made a custom board where a button is attached to P0_6. The button is configured as INPUT_PULLUP and connected to 3.3V and a resistance. Whenever I tried to debug it using Keil works perfectly. It shows 0 on the LightBlue app and 1 when it's pressed. But when I tried using SmartSnippets Toolbox it shows 1 all the time, so I can´t activate the interruption.
I looked at the board setup in SmartSnippets and one of the SPI ports was using P0_6 so I changed it to a port I don't use. But still, I have the same issue.
Any idea why is this happening?
定制DA14580董事会——延长睡眠不工作
Hi,
I have purchased a custom DA 14580 beacon tag hardware. While running the ble_app_barebone project, the advertisement works fine when sleep is disabled. But, on setting the app_default_sleep_mode to ARCH_EXT_SLEEP_ON, the device execution stops abruptly after first few advertisements. Please suggest the possible reasons for the same.
Thanks
Wisilica
DA9230 and DA9231, Dialog Semiconductor’s First Nanopower PMICs
Dialog Semiconductor’s first nanopower PMICs extend battery life for always-on connected applications. The ultra-compact DA9230 and DA9231 nanopower PMICs provide high efficiency and flexibility for wearables, smart door locks, portable medical devices and more.
Clickherefor more information
Can I consider the High-Z input GPIO as a FLOATING pin to a capacitive load?
We are developing a sensing system using DA14580, to perform C-V transition .In some cases , we need to connect GPIO to capacitive sensor's electrode , set it to floating in order to mute this capacitive sensor.
We do not know the exact structure of the DA14580 GPIO.
If we config the GPIO as High-Z input, can we consider it as a floating pin to a capacitive load? Is there some risks to use GPIO pin in this method?
Thanks for any advice!
请问，DA14580的GPIO 设置为High-Z input 对于外部负载可否视为浮空？
各位好！
我们目前在用DA14580 开发一套系统，进行容性传感器的CV转换和采集，需要将某些GPIO接到容性负载的一端。出于检测需要，有时候需要将这一端设为浮空状态。
请问DA14580内部的GPIO结构是怎样的？当把IO引脚设置为High-Z input 模式时，对外部容性负载可否视为浮空？当容性负载的另一端电平有变化时，浮空端引起的感应电荷是否会影响GPIO输入导致诸如不可控的电流倒灌之类的情况。
多谢！
Codeless AT commands for SPI sensor support
Hello,
Could you please give a rough estimate as to when the SPI support with AT commands could be available for interfacing sensors with 580 ?
I am in urgent need for such an interface and haven't been able to establish such an interface with the SPI library available in the SDK.
Thank you for your response,
Eren
Pages
