Hello,
I have the following questions:
1. What is the power consumption in idle state with no clock enable?
2. What is the power consumption in idle state with the 2.048MHz clock enable?
3. How do I download the software?
Thank you,
Fernando
hi,
I wrote a new AT Command with 1wire:
否则if（user_compare_cmd（“1wire”，1,2）））
{
TM_OneWire_t OW;
uint8_t port = ahtoi((char*)argument_array[0]);
uint8_t port_number = port / 10;
UINT8_T PIN_NUMBER =端口％10;
uint8_t DS_ROM[8];
char message[8];
float temp;
TM_OneWire_Init(&OW, (GPIO_PORT)port_number, (GPIO_PIN)pin_number);
TM_OneWire_Reset(&OW);
Hi!
I have bought a HJ-580LA BLE module and loaded it up with CodeLess firmware as guided by the youtube tutorial by Lucid Dev Team.
I can access the programmed module via UART and use AT command to configure it.
我关闭了睡眠模式，将其设置为外设，并将其设置为广告模式。
The module appears under the bluetooth devices of my win10 PC and sony xperia smartphone, but not Xiaomi mi4 phone.
When I try to connect to it with Android Dialog DSPS on xperia then after pressing "SCAN" the app reports "No devices found".
Hello,
we want go with the DA9062 for a small Zynq board. I saw there are some shematic files available - they look like altium files but altium doesn't open the files.
一个re the some schematic reference files for altium available for the DA9062?
thanks
Alex
Hi I am working on the HJ580LA module which houses the DA14580 chip. I have installed the DSPS code, but I have a problem: when there is no uart device between ble and the mobile device I can see and connect to the module via the "Dialog dsps" application , but if I use another uart device connected to this ble module ı can't see the ble device from the mobile device.
Hello Dialog Team,
I'm following “AN-B-007 DA1458x Bluetooth Direct Test Mode” to learn how can we test the product on the lab.
我正在使用SmartSnippets Burn Prod_Test_580.bin，但我不知道如何识别我的电路板是否为实验室测试准备。
I don't have the equipaments discrebed on the document to check if the firmware it is working or not. I tested the harware with my custom firmware application is working very well and the hardware is perfect.
Hi Dialog,
I need to make a new medical profile that mesures the respiration's rate . After months of trying I have made the HRPS profile working but using the sdk3 since I have wasted a lot of time on sdk5 and all the documents you have are for sdk3. But when following the UM-B-003 and UM-B-029 I have many errors or it is not working .So I am confused what should I do to make this new profile? or have someone made this profile or a similar one ? I am new to all this and don't have experience could you please give me a detailed explication
Hello Support Team,
I need to know the minimum program - erase cycles of the internal SPI Flash.
Thanks for the support.
Hi,
I have written a code to sample P00, P01, P02 ADC Values.
This code is triggered by codless AT+TMRSTART=0,0,1
The code looks like:
else if(user_compare_cmd("TMRSTART",3,3))
{
uint8_t timer_id = ahtoi((char*)argument_array[0]);
uint8_t指数= ahtoi ((char *) argument_array [1]);
times_seconds= ahtoi((char*)argument_array[2]);
Hello,
I would like some clarification on the DA7212 System Clock. From the datasheet it seems that we can provide the codec with frequencies 2-50MHz. However the Beep Generator section (13.9) talks about 12.288MHz and 11.288MHz. If we provide MCLK of 4MHz will the beep generator still work?
Also if we us the codec for analog paths only (no I2S digital interface) do we need to provide an MCLK? Same question for beep generator, does MCLK need to be provided?
thanks!
