Basic Kit - Flash programing

7 posts / 0 new
Last post
Fri, 2015-03-27 15:33
#1
sbourahla
Offline
Last seen:5 years 6 months ago
Expert
Joined:2015-02-25 09:51
Basic Kit - Flash programing

Hello,

I try to program the 14580-Basic-Kit flash (on SPI) with the J-LINK and Keil 5, but i obtain the error : Flash Download Failed - "Cortex-M0". For this I follow the User Guide UM-B-025.

I also try to program this flash with the SmartSnippets software, I have error too :

[ACTION @15-03-27 16:29:03] Please press the hardware reset button on the board to start the download process.
[ERROR @15-03-27 16:29:10] Timeout: Reset signal not detected for more than 8000 msecs.

I try the two configurations for the J4 connector.

Any suggestions ??

Mon, 2015-03-30 09:20
RvA
Offline
Last seen:2 days 5 hours ago
Staff
Joined:2014-02-07 14:10
Hi sbourahla

Hi sbourahla

There is some information missing in the User Manual that will be added later. Connection of the DEVKTs should be like the photos show:

A black ‘3-way jumper’ is required to connect SPI MISO – P05 – T_TxD.

Can you try again with smartsnippets to program the SPI memory?

Mon, 2015-03-30 10:27
(Reply to #2)
sbourahla
Offline
Last seen:5 years 6 months ago
Expert
Joined:2015-02-25 09:51
With this jumper

With this jumper configuration, I have the same result :

[ACTION @15-03-30 11:30:00] Please press the hardware reset button on the board to start the download process.
[ERROR @15-03-30 11:30:06] Timeout: Reset signal not detected for more than 8000 msecs.

Mon, 2015-03-30 13:25
RvA
Offline
Last seen:2 days 5 hours ago
Staff
Joined:2014-02-07 14:10
You did press the reset

You did press the reset button?

We tried here as well and followed these steps

1. made the three-way jumper

2.连接,如图片所示。其他障碍物per settings:

3. Via SmartSnippets software can be downloaded into SPI flash through the USB- and the virtual com-port.

Mon, 2015-03-30 16:20
sbourahla
Offline
Last seen:5 years 6 months ago
Expert
Joined:2015-02-25 09:51
@RvA,

@RvA,

I already do this, ii doesn't work.

I try some manipulation, i succeeded to program sometimes the flash.

But now again, it's impossible, i have this error :
[INFO @15-03-30 17:21:19] Started burning memory with 27632 bytes of data at address 0x00000.
[INFO @15-03-30 17:21:19] Connection to COM10 port has successfully opened.
[ERROR @15-03-30 17:21:32] Timeout while waiting to receive the most significant byte of packet length (10000 msecs)
[INFO @15-03-30 17:21:32] Successfully disconnected from port COM10.
[ERROR @15-03-30 17:21:32] Memory burning failed.

I have already verify the connection and the jumper. Any suggestions ?

Fri, 2015-04-03 15:28
RvA
Offline
Last seen:2 days 5 hours ago
Staff
Joined:2014-02-07 14:10
Hi sbourahla,

Hi sbourahla,

I have sent you an email for getting some details like pictures of your board and screenshots of smartsnippets.

Best regards, RvA

Tue, 2015-04-07 13:13
(Reply to #6)
sbourahla
Offline
Last seen:5 years 6 months ago
Expert
Joined:2015-02-25 09:51
Hi RvA,

Hi RvA,

I see your email, I reply only this morning because we had some national holidays here.

Best Regards,