Can't connect to DA14531 after putting it in hibernation | Dialog Semiconductor customer support - 雷电竞下载app,雷电竞官网登录,雷竞技安卓下载

13 posts / 0 new

Last post

Wed, 2020-09-16 09:57

innovativepower

Offline

Last seen:3 months 2 weeks ago

Joined:2020-09-07 17:16

Can't connect to DA14531 after putting it in hibernation

Hello,

I tried to get the DA14531 module in hibernation with theda14531_configuring_da14531_hibernation_modeexample code. This example was not working properly, because I measured a current consumption of 10uA, both on the power profiler and a multimeter. After trying to flash a different example, I couldn't get the module to connect on the pro devkit. I've had similar problems before, but when I flashed the module via UART it worked fine again. Now, the module isn't responding to SWD, 1-wire UART, 2-wire UART, and SPI.

Is there a way to recover the module from its hibernation?

Thanks,
Martin

Keywords:

#da14531 #pro dev board #hibernation

Device:

DA14531 SmartBond TINY Module

Wed, 2020-09-16 15:57

PM_Dialog

Offline

Last seen:1 day 6 hours ago

Joined:2018-02-08 11:03

Hi innovativepower,

Thanks for your question and for your interest in our DA14531 Module BLE solution.

Please let me check it in detailed and I’ll get back to you as soon as possible.

Thanks, PM_Dialog

Tue, 2020-09-22 14:48

PM_Dialog

Offline

Last seen:1 day 6 hours ago

Joined:2018-02-08 11:03

Hi Martin,

Apologies for my delay response. Can I ask what is the SDK version that you are using?

Please try to boot with a different from 1-wire UART on P05 which a prior step than booting from the external SPI Slave in the booting sequence. Please see section 6 Booting from 1-wire UART from the following application note.

//www.wsdof.com/sites/default/files/an-b-072-da14531_booting_options_v1.4.pdf

Once the device booted, then try to connect to the SPI flash and erase it.

Thanks, PM_Dialog

Wed, 2020-09-23 08:57

innovativepower

Offline

Last seen:3 months 2 weeks ago

Joined:2020-09-07 17:16

Hi,

我试着引导我t from 1-wire UART, but the module is not responding to a reset.

I'm using SDK 6.0.14.1114

Thanks,
Martin

Wed, 2020-09-23 10:47

PM_Dialog

Offline

Last seen:1 day 6 hours ago

Joined:2018-02-08 11:03

Hi Martin,

Could you please indicate if you are using the Pro-DK or a custom board? In case of Pro-DKm please check if you are using the correct jumper configuration. See 5.9.1 Single wire UART, JTAG, RESET inUM-B-141: DA14531 SMARTBOND TINY™ MODULE Development Kit Pro Hardware User Manual.

Thanks, PM_Dialog

Fri, 2020-09-25 10:50

innovativepower

Offline

Last seen:3 months 2 weeks ago

Joined:2020-09-07 17:16

Hi,

I'm using the Pro-DK and I followed the instructions in the manual with the correct jumper settings.

Thanks,
Martin

Mon, 2020-09-28 15:23

PM_Dialog

Offline

Last seen:1 day 6 hours ago

Joined:2018-02-08 11:03

Hi Martin,

I am able to boot form 1-wire UART in my side. Can you please check if the P0_5, P0_5, 115200 Bd is selected in the Board Setup?

Please see Figure 20 Single UART communication.

http://lpccs-docs.dialog-semiconductor.com/UM-B-083/tools/Board_Setup.html

Thanks, PM_Dialog

Mon, 2020-09-28 21:03

innovativepower

Offline

Last seen:3 months 2 weeks ago

Joined:2020-09-07 17:16

Hi,

Yes, P05 is selected and it still doesn't connect. The problem seems to be that the module is not resetting, with the button on the mother board as well as the button on the daughter board.

Thanks,
Martin

Mon, 2020-10-05 17:04

PM_Dialog

Offline

Last seen:1 day 6 hours ago

Joined:2018-02-08 11:03

Hi Martin,

Can you please send a log file from the SmartSnippets Toolbox? Additionally can you please probe the P00? A high signal on P00 will generate a reset.

Thanks, PM_Dialog

Tue, 2020-10-06 09:06

# 10

innovativepower

Offline

Last seen:3 months 2 weeks ago

Joined:2020-09-07 17:16

Hi,

I tried probing the pin with a logic analyser, and P00 stays low all the time. On P05 a message is sent prior to resetting the module: {0x00, 0x01, 0x49, 0x66, 0x2D, 0x3D, 0xC0}. The voltage on P00 is about 40mV when pressing the button, so it may be held low by a GPIO pin? When I forced the pin high for a very short time, it didn't have any effect.

This is the log file when attempting to flash:

[INFO SPI Flash @20-10-06 09:44:49] Firmware File /home/martin/DiaSemi/SmartSnippetsStudio2.0.14/Toolbox/common_resources/SupportPackages/DA1453x/tool box_resources/common/flash_programmer_531.bin has been selected for downloading. [INFO SPI Flash @20-10-06 09:44:49] Connection to /dev/ttyUSB0 port has successfully opened. [INFO SPI Flash @20-10-06 09:44:49] Started download procedure... [ACTION SPI Flash @20-10-06 09:44:50] Please press the hardware reset button on the board to start the download process. [ERROR SPI Flash @20-10-06 09:44:57] Timeout: Reset signal not detected for more than 8000 msecs. [INFO SPI Flash @20-10-06 09:44:57] Please try again. If problem persists refer to User Manual AN-B- 072 (//www.wsdof.com/an-072-booting-from-serial- interface) and check jumper settings. For booting from 2- wire UART (P0_0 and P0_1) see Figure 10. For booting from 1-wire UART P0_5 see Figure 6. [INFO Booter @20-10-06 09:44:57] Successfully disconnected from port /dev/ttyUSB0. [ERROR SPI Flash @20-10-06 09:44:57] Failed downloading firmware file to the board.

Thanks,
Martin

Tue, 2020-10-06 14:13

# 11

PM_Dialog

Offline

Last seen:1 day 6 hours ago

Joined:2018-02-08 11:03

Hi Martin,

Please probe the P05 using a logic analyzer. Once the reset button is pressed and the chip reboots, you should see the 0x02 on the P05. Can you verify this one?

Thanks, PM_Dialog

Tue, 2020-10-06 15:29

# 12

innovativepower

Offline

Last seen:3 months 2 weeks ago

Joined:2020-09-07 17:16

Hi,

When I tried to capture the sequence with a logic analyser, I accidentally discovered a fix. When the chip booted, there was no way of resetting it, because the chip held the reset pin low. Forcing the reset pin high did not help.

I accidentally left the logic analyser running while power cycling the pro dk(re-plugging the USB). On the log I saw P00(reset) going high and P05 responded with the 0x02 you mentioned. So, the module does respond to a reset prior to booting.

I was able to flash the board again by power cycling the module while trying to connect to it via the smartsnippet toolbox. This can be done by unplugging the daughter board from the main board, and then plugging it back in when the log asks you to reset the module. Then the reset is detected, because the module hasn't booted yet, after which I flashed the module.

Thanks for your time,
Martin

Wed, 2020-10-07 16:34

# 13

PM_Dialog

Offline

Last seen:1 day 6 hours ago

Joined:2018-02-08 11:03

Hi Martin,

高兴你找到你的问题。如果你有any follow-up question, please raise a new forum post.

Thanks, PM_Dialog