Dear,
When I use the GPAK with bread board and some discrete components,
I tried without USB cable connected, and connect the VDD pin to power supply, it seems not working.
Do I need to connect the USB cable with GPAK to power up? Or just connnect the VDD pin on GPAK to 5V power supply?
In addition, in GPAK Designer program emluation mode, the LED on advanced board was turned on depending on the output.
Does the LED turn on depending on the output even in practical application?
(I mean using GPAK with other discrete components for experiment, not emulating)
Thanks,
Regard.
Device:
Device Number:
SLG46517M
Dear Yuseungho,
Yes, you must connect and power up USB if you want to test your design on board. Of course, you can separate to socket with the programmed chip and test it on the socket, without using the board.
Regarding the LEDs on board, they are driven by the chip through the buffers. These buffers are enabled by FPGA onboard. In the practical application, we usually program the chip and run it in Test Mode (not Emulation) and you can use some discrete external components. I recommend using EC (expansion connectors) for applying digital signals and TP connectors for analog signals.
Best regards,
Oleh Sapiha
Thank you for your help.
我不明白的是，如果我想使用GPAK，我总是必须运行GPAK设计师程序并通过USB连接它吗？
I've already checked the chip is working properly in test mode, then I want to apply GPAK to the actual circuit.
但是没有GPAK设计者程序，即使将外部电源应用于VDD引脚，它似乎并没有启动。
I have used the oscilloscope to see whether it's working without the program running or not, no signals were found.
Of course it works with the program running and applying external power to the VDD pin.
The question sounds a little silly. Anyway, Thank you for your help.
Best regards.
Yuseungho,
Thanks for your question,
After you have programmed the chip with your design, you need neither board nor socket, just solder your chip on the PCB and it will behave according to your design. Don't forget to connect VDD and GND pins to power up the IC.
I don't know why it doesn't work, can you show me your connections? Be sure that the chip is programmed.
Best regards,
Oleh Sapiha
There was a misunderstanding about how it works. I thought the advanced board could also be operated using external power.
If you don't mind may I ask you another question?
In test mode, the state changes depending on the ASM state and the TP pin LED lights up according to the current state.
I unplugged the advanced board and used the socket to test it with my circuit, then I found the chip could not reach the next state.
For example, I set the LED of the initial state(S0) is TP 3, and with input signal 'a' the state changes to the next state(S1) which is TP 4.
在测试模式下，当应用VDD时，TP3亮起，我申请了信号'A'，然后TP4亮起。
But with the programmed chip inserted in the socket, after the VDD is applied, TP3 actuallys lights up, so I applied signal 'a', but TP4 does not light up.
Does the ASM have any required conditions? Or any other problem that might be happened?
(Of course, it will be very difficult for you to say what the exact problem is without watching the chip.)
Thank you so much for answering so many questions.
问候
Yuseungho,
If you don't supply the board the LED will not light up. As I told, LEDs are driven through buffers, which are enabled by FPGA. So, if the board is not supplied (FPGA isn't ON) and LED couldn't be driven. If you want to test the IC without board you must use the scope, but not LEDs on board
Best regards,
Oleh Sapiha
Yuseungho,
We can have a short call, let's say in MS Teams, Skype for business or Zoom, so you can show me your design and the problems you faced with. I will try to help you with the testing.
Best regards,
Oleh Sapiha
Yuseungho,
Oleh.sapiha @ diasemi.com.this is my email, please write me a letter and we will discuss the call
Best regards,
Oleh Sapiha
Thank you very much.
I have already sent the email, please check the email.
问候，