DA1458X Mass production

Hi Rohit,

对于大规模生产，请检查生产线工具（PLT）。最多16个设备可以连接..

https://www.dialog-seminile.com/produ雷电竞官网登录cts/production-line-tool.

Are you using this tool for the production?

谢谢，PM_DIALOG.

Hi Rohit,

请从以下文档中查看7.2.4 BD地址。

https://www.dialog-seminile.com/sites/default/files/um-b-041_da1458x_da1468x_production_line_tool_4v2.pdf.

Could you please clarify what you would like to accomplish with BD address? What is your requirement in production?

谢谢，PM_DIALOG.

Hi Rohit,

When the PLT is used, the BD address will be programmed into the OTP Header. After that, the device will get the BD address of the OTP Header, so any other BD address in the NVDS or in application code will be ignored. During production, the code will not be affected, but as mentioned before the PLT will write the OTP header with the appropriate BD address. Regarding your last question, could you please clarify it? Please note that the OTP stands for One-Time-Programmable, thus it cannot be written multiple times.

谢谢，PM_DIALOG.

Hi Rohit,

If you are planning to use the PLT for the production, and in case you want to burn the BD address through the PLT, the BD address will be stored in the appropriate field of the OTP Header. This field can but burnt without the PLT as well, so if you have plenty of boards you can do some tests. You can use the use the SmartSnippets Toolbox to read and write the OTP Header.

>>>And What is the effect If I am using Flash for production?

In case of the BD address is programmed to the OTP Header? So, if I understood correctly you are using a DA14580 and a DA14583 in your design, Do you want to program both through the PLT (assume with different fw) ? And what about the BD address?

谢谢，PM_DIALOG.

Hi Rohit,

In all cases, if you are using the PLT to burn the BDA, then it will be stored in the OTP Header. Then the DA1458x will start advertising with the BDA from the OTH Header. Please check nvds_read_bdaddr_from_otp(). Do you mean to burn the BDA in the OTP Hader and then read it from you FW?

谢谢，PM_DIALOG.

Hi Rohit,

如果设备BD地址在OTP标题中写入，则忽略CFG_NVDS_TAG_BD_ADDRESS值。如果检查system_init（）函数，则会看到SDK检查并读取BD地址 - NVDS_READ_BDADDR（）。如果检查上述功能，您将看到：

In case if DA14583, the SDK first checks and reads BD address from DA14583's internal SPI flash - nvds_read_bdaddr_from_da14583_flash().. If no BD address is found in flash, then tries to read BD address from OTP - nvds_read_bdaddr_from_otp().

In case of DA14580, as it does not contain an embedded SPI Flash, the SDK checks only the OTP Header - nvds_read_bdaddr_from_otp().

如果读取NVDS_READ_BDADDR_FROM_OTP（）的源代码，您将看到如何读取从0x7fd4地址（bdaddr_offset）启动的OTP标题的BD地址。

谢谢，PM_DIALOG.

Hi Rohit,

在dev_bdaddr中会复制OTP_BDADDR。

memcpy(&dev_bdaddr, otp_bdaddr, sizeof(dev_bdaddr));

如果在SDK中搜索一点点，您将找到以下内容：

/// Device BD address

struct bd_addr dev_bdaddr __attribute__((section("retention_mem_area0"), zero_init));

SDK已检索OTP_BDADDR。因此，这取决于您 - 您可以使用此功能或实现基于NVDS_READ_BDADDR_FROM_OTP（）的功能，您需要做的就是从OTP读取正确的地址。

谢谢，PM_DIALOG.

Hi Rohit,

Sorry, bur I am little bit confused, so could you please indicate what you are trying to accomplish? Did you burn the OTP with your firmware, or did you burn the OTP Header with a specific BDA? Just try to connect to the OTP Header from the SmartSnippets Toolbox and burn your BDA.

Still I am not completely sure if I have understood your requirement. If I understood correctly you have 2 different products. The first one in based on DA14580 and the second on the DA14583.

您希望使用PLT并使用特定的BDA刻录OTP标头。出于测试目的，您可以使用SST才能刻录BD地址。你燃烧了OTP标题吗？

谢谢，PM_DIALOG.

Hi Rohit,

Apologies for the delay. Externign the dev_bdaddr could be a possible approach. The device obtains the bd address during start up, in the nvds_read_bdaddr() function (the device checks from the where the bd address can be obtained either NVDS structure or OTP) and places the obtained value in the dev_bdaddr variable that holds the address of the device.

你能澄清＃3步吗？

>>>in user_peripheral file - using dev_bdaddr->addr[5]; accessed address and assigned in advertising variable

Do you mean that you want to add the bd address in the advertising string?

As I have already mentioned, you should burn the BD Address in the OTP Header. Please use the Smart Snippets toolbox in order to read and burn the OTP Header. You will not need to burn the whole application image into OTP and boot from there

谢谢，PM_DIALOG.

Hi Rohit,

对不起，可能我错过了你最后的评论。您是否意味着您应该遵循的步骤，以便通过Smart Scippets Toolbox刻录OTP标头中的BDA？

If yes, you could use the CLI in order to burn the BD Address in the OTP Header. The CLI can be found under \5.0.4\binaries\host\windows\prod_test_cmds SDK path. The following command will write the BD Address into OTP:

prodtest - p < COM端口号> otp wr_bdaddr < BD广告dress>

示例：Prodtest -P 14 OTP WR_BDADDR 44：49：41：4C：4F：47

另一个选项可能是使用SmartSnippets Toolbox才能在OTP标题中刻录BD地址。通常，对于通过SST刻录OTP，您应该是OTP程序员。请记住，建议使用最新版本的工具。

The OTP has 3 areas where the user can burn data:

• The OTP image area, where the user code is placed and mirrors to the sysram at boot.
• OTP NVDS区域，其中NVDS结构在启动时填充了OTP。
• The OTP Header area, where flags and specific values that define the operation of the device are placed (more information regarding the values of the OTP Header can be found in the Smart Snippets User guide).

When burning the OTP, you should make sure that the programming voltage is clean and must not exceed 6.8V. Please refer to the datasheet to find more details for the programming voltage. Keep in mind that OTP stands for One Time Programmable, thus you can’t erase and re-write the OTP multiple times, but you can only flip the bits that are still set to 0 and turn them to 1.

在您的情况下，打开SST并连接到OTP标题。只要您已连接，您将看到OTP标题中的所有可用字段。PLT将在“设备唯一ID”字段中的以下地址中存储BD地址。

So, if you would like to test it, you should burn the BD address in the “Device unique ID” field. Please note that, the most significant (left-most) byte of a word is stored in the smallest address (big-endian). E.g. if a user types 0A0B0C0D for field ‘Device Unique ID’, 0x0A will be written at 0x47FD4 and 0x0D will be written at 0x47FD7.

谢谢，PM_DIALOG.