DA7212 MKRZERO接口

你好,

附上我手上的DA7212的数据表。

问候,

Niradat

你好查尔斯,

感谢分享更新后的DA7212 Datasheet。使用数据表，我已经在Arduino MKRZERO上编写了以下代码。在这段代码中，MKRZERO正在播放一个16位立体声WAV文件，我可以在我的ARD-AUDIO-DA7212音频屏蔽上听它。但似乎DA7212突然进入睡眠状态，音频停止。虽然MKRZERO正在播放音频。此外，从DA7212模块的音频不是立体声。请在这方面给予帮助。

最好的问候,

NIradat。

#define CODEC_ADDRESS 0x1A #include  #include < arduinsound .h> #include  // wave file to play const char filename[] = "MUSIC.WAV";//变量代表波浪文件SDWaveFile;void setup(){//打开串行通信并等待端口打开:serial .begin(9600);延迟(5000);// setup the SD card, depends on your shield of breakout board //你可能需要通过一个pin number in begin for SS Serial。打印(“初始化SD卡…”);if (!SD.begin()) {Serial. start ();println(“初始化失败!”);返回;}系列。println(“初始化完成。”); // create a SDWaveFile waveFile = SDWaveFile(filename); // check if the WaveFile is valid if (!waveFile) { Serial.println("wave file is invalid!"); while (1); // do nothing } // print out some info. about the wave file Serial.print("Bits per sample = "); Serial.println(waveFile.bitsPerSample()); long channels = waveFile.channels(); Serial.print("Channels = "); Serial.println(channels); long sampleRate = waveFile.sampleRate(); Serial.print("Sample rate = "); Serial.print(sampleRate); Serial.println(" Hz"); long duration = waveFile.duration(); Serial.print("Duration = "); Serial.print(duration); Serial.println(" seconds"); ///////////////////////////////////////////////////////////////////// Initialization of DA7212 ///////////////////////////////////////////////////////////////// Wire.begin(); //WRITE DA7212 0x92 0x00 //Set Ramp rate to default delay(100); Wire.beginTransmission(CODEC_ADDRESS); Wire.write(0x92); Wire.write(0x00); Wire.endTransmission(); //WRITE DA7212 0x90 0x80 //Enable Digital LDO delay(100); Wire.beginTransmission(CODEC_ADDRESS); Wire.write(0x90); Wire.write(0x80); Wire.endTransmission(); //WRITE DA7212 0x29 0xC0 //Enable AIF 16bit I2S mode delay(100); Wire.beginTransmission(CODEC_ADDRESS); Wire.write(0x29); Wire.write(0xC0); Wire.endTransmission(); //WRITE DA7212 0x22 0x0A //Set incoming sample rate to 44.1kHz delay(100); Wire.beginTransmission(CODEC_ADDRESS); Wire.write(0x22); Wire.write(0x0A); Wire.endTransmission(); //WRITE DA7212 0x94 0x02 //Set PC sync to resync default delay(100); Wire.beginTransmission(CODEC_ADDRESS); Wire.write(0x94); Wire.write(0x02); Wire.endTransmission(); //WRITE DA7212 0x27 0x04 //PLL_CTRL PLL disabled delay(100); Wire.beginTransmission(CODEC_ADDRESS); Wire.write(0x27); Wire.write(0x04); Wire.endTransmission(); //WRITE DA7212 0x2A 0x32 //Route DAI to Outputs default delay(100); Wire.beginTransmission(CODEC_ADDRESS); Wire.write(0x2A); Wire.write(0x32); Wire.endTransmission(); //WRITE DA7212 0x4B 0x08 //MIXOUT_L input from DACL delay(100); Wire.beginTransmission(CODEC_ADDRESS); Wire.write(0x48); Wire.write(0x08); Wire.endTransmission(); //WRITE DA7212 0x4C 0x08 //MIXOUT_R input from DACR delay(100); Wire.beginTransmission(CODEC_ADDRESS); Wire.write(0x4C); Wire.write(0x08); Wire.endTransmission(); //WRITE DA7212 0x47 0xCD //Enable charge pump, CP_MOD mode, CPVDD/1 and Boost CP delay(100); Wire.beginTransmission(CODEC_ADDRESS); Wire.write(0x47); Wire.write(0xCD); Wire.endTransmission(); //WRITE DA7212 0x95 0x36 //Set CP threshold to 0x36 delay(100); Wire.beginTransmission(CODEC_ADDRESS); Wire.write(0x95); Wire.write(0x36); Wire.endTransmission(); //WRITE DA7212 0x96 0xA5 //Set CP Tau DELAY to 64ms delay(100); Wire.beginTransmission(CODEC_ADDRESS); Wire.write(0x96); Wire.write(0xA5); Wire.endTransmission(); //WRITE DA7212 0x48 0x2D //Set volume to -12dB delay(100); Wire.beginTransmission(CODEC_ADDRESS); Wire.write(0x48); Wire.write(0x2D); Wire.endTransmission(); //WRITE DA7212 0x49 0x2D //Set volume to -12dB delay(100); Wire.beginTransmission(CODEC_ADDRESS); Wire.write(0x49); Wire.write(0x2D); Wire.endTransmission(); //WRITE DA7212 0x51 0xF1 //Enable DAC, Mix and HP amplifiers delay(100); Wire.beginTransmission(CODEC_ADDRESS); Wire.write(0x51); Wire.write(0xF1); Wire.endTransmission(); //WRITE DA7212 0xFD 0x01 //Set tone gen gain to -18dBstem Active delay(100); Wire.beginTransmission(CODEC_ADDRESS); Wire.write(0xFD); Wire.write(0x01); Wire.endTransmission(); ///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////// // adjust the playback volume AudioOutI2S.volume(50); // check if the I2S output can play the wave file if (!AudioOutI2S.canPlay(waveFile)) { Serial.println("unable to play wave file using I2S!"); while (1); // do nothing } // start playback Serial.println("starting playback"); AudioOutI2S.play(waveFile); } void loop() { // check if playback is still going on if (!AudioOutI2S.isPlaying()) { // playback has stopped Serial.println("playback stopped"); while (1); // do nothing } }