Hello, I'm trying to burn internal flash memory over JTAG. But get an error:
[错误SPI Flash @ 19-02-28 17:51:23] JTAG地址0x7FC7C0C的AddDition Error Info。（MSB第一）：FF FF FF F8。
[ERROR SPI Flash @19-02-28 17:51:23] Memory burning failed.
I have tried two configurations:
SPI_CLK: P2_0
SPI_EN: P2_3
SPI_DI：P2_4
SPI_DO: P2_9
and
SPI_CLK: P2_0
SPI_EN: P2_3
SPI_DI：P2_9.
SPI_DO: P2_4
Keywords:
Device:
Hi azimin,
Do you mean that you have the configurations you have mentioned in the Configuration window of SmartSnippets toolbox? Also, do you have a custom board, or you are using any of our development boards? If you try to connect over UART, could you please let me know if you are able to connect/burn successfully? Also, are you able to connect/erase the SPI flash over JTAG or your only issue is that you can not burn it?
Thanks, PM_Dialog
>您是否意味着您拥有SmartSnippets Toolbox的配置窗口中提到的配置？
Yes
>同时,你有一个定制的,或者你是强的g any of our development boards?
I have a custom board
> If you try to connect over UART, could you please let me know if you are able to connect/burn successfully?
首次我通过UART成功连接，但不能刻录或擦除固件。在此故障后，我无法再次连接，工具箱正在等待按重置按钮，但我没有它。
[INFO SPI Flash @19-03-01 11:53:51] Firmware File C:\DiaSemi\DA14585_SDK\6.0.10.511\config\toolbox_resources/common/flash_programmer.bin has been selected for downloading.
[INFO SPI Flash @19-03-01 11:53:51] Connection to COM16 port has successfully opened.
[INFO SPI Flash @19-03-01 11:53:51] Started download procedure...
[INFO Booter @19-03-01 11:53:53] Successfully disconnected from port COM16.
[INFO SPI Flash @19-03-01 11:53:53] Connection to COM16 port has successfully opened.
[INFO Booter @19-03-01 11:53:53] Successfully disconnected from port COM16.
[INFO SPI Flash @19-03-01 11:53:53] Successfully downloaded firmware file to the board.
[INFO SPI Flash @19-03-01 11:53:53] Successfully configured SPI Flash ports and pins.
[INFO SPI Flash @19-03-01 11:53:58] Started reading 32768 bytes from memory.
[INFO SPI Flash @19-03-01 11:53:58] Connection to COM16 port has successfully opened.
[INFO Booter @19-03-01 11:54:05] Successfully disconnected from port COM16.
[INFO SPI Flash @19-03-01 11:54:05] Reading has finished. Read 32768 bytes.
[INFO SPI Flash @19-03-01 11:55:08] Header records have been removed from hex file prox_reporter_586.hex.
[INFO SPI Flash @19-03-01 11:55:08] Read 29872 bytes from file prox_reporter_586.hex.
[INFO SPI Flash @19-03-01 11:55:13] Started burning memory with 31016 bytes of data at address 0x00000.
[INFO SPI Flash @19-03-01 11:55:13] Connection to COM16 port has successfully opened.
[ERROR SPI Flash @19-03-01 11:55:18] Received error message while checking whether burning was successful: FFFFFFF8.
[INFO Booter @19-03-01 11:55:18] Successfully disconnected from port COM16.
[ERROR SPI Flash @19-03-01 11:55:18] Memory burning failed.
[INFO SPI Flash @19-03-01 11:55:32] Started burning memory with 31016 bytes of data at address 0x00000.
[INFO SPI Flash @19-03-01 11:55:32] Connection to COM16 port has successfully opened.
[ERROR SPI Flash @19-03-01 11:55:37] Received error message while checking whether burning was successful: FFFFFFF8.
[INFO Booter @19-03-01 11:55:37] Successfully disconnected from port COM16.
[ERROR SPI Flash @19-03-01 11:55:37] Memory burning failed.
[INFO SPI Flash @19-03-01 11:55:49] Connection to COM16 port has successfully opened.
[ERROR SPI Flash @19-03-01 11:55:49] Received error message while checking whether SPI erase was successful: FFFFFFFE.
[INFO Booter @19-03-01 11:55:49] Successfully disconnected from port COM16.
[ERROR SPI Flash @19-03-01 11:55:49] SPI Memory erasing failed.
[INFO SPI Flash @19-03-01 11:56:07] Firmware File C:\DiaSemi\DA14585_SDK\6.0.10.511\config\toolbox_resources/common/flash_programmer.bin has been selected for downloading.
[INFO SPI Flash @19-03-01 11:56:08] Connection to COM16 port has successfully opened.
[INFO SPI Flash @19-03-01 11:56:08] Started download procedure...
[INFO Booter @19-03-01 11:56:09] Successfully disconnected from port COM16.
[INFO SPI Flash @19-03-01 11:56:10] Connection to COM16 port has successfully opened.
[info booter @ 19-03-01 11:56:10]成功与COM16端口断开了连接。
[INFO SPI Flash @19-03-01 11:56:10] Successfully downloaded firmware file to the board.
[INFO SPI Flash @19-03-01 11:56:10] Successfully configured SPI Flash ports and pins.
[INFO SPI Flash @19-03-01 11:56:13] Connection to COM16 port has successfully opened.
[INFO Booter @19-03-01 11:56:13] Successfully disconnected from port COM16.
[INFO SPI Flash @19-03-01 11:56:13] SPI Memory erasing completed successfully.
[INFO SPI Flash @19-03-01 11:56:13] Reading memory to verify its contents after erase...
[INFO SPI Flash @19-03-01 11:56:13] Connection to COM16 port has successfully opened.
[ERROR SPI Flash @19-03-01 11:56:13] Received error message while reading from the board: FFFFFFFC.
[INFO Booter @19-03-01 11:56:14] Successfully disconnected from port COM16.
[ERROR SPI Flash @19-03-01 11:56:14] Failed reading memory.
[INFO SPI Flash @19-03-01 11:56:14] Reading memory to refresh its contents....
[信息SPI Flash @ 19-03-01 11:56:14]连接到COM16端口已成功打开。
[ERROR SPI Flash @19-03-01 11:56:14] Received error message while reading from the board: FFFFFFFC.
[INFO Booter @19-03-01 11:56:14] Successfully disconnected from port COM16.
[ERROR SPI Flash @19-03-01 11:56:14] Failed reading memory.
[INFO SPI Flash @19-03-01 11:58:03] Started reading 32768 bytes from memory.
[INFO SPI Flash @19-03-01 11:58:03] Connection to COM16 port has successfully opened.
[ERROR SPI Flash @19-03-01 11:58:03] Received error message while reading from the board: FFFFFFFC.
[INFO Booter @19-03-01 11:58:03] Successfully disconnected from port COM16.
[ERROR SPI Flash @19-03-01 11:58:03] Failed reading memory.
[INFO SPI Flash @19-03-01 11:58:06] Firmware File C:\DiaSemi\DA14585_SDK\6.0.10.511\config\toolbox_resources/common/flash_programmer.bin has been selected for downloading.
[INFO SPI Flash @19-03-01 11:58:06] Connection to COM16 port has successfully opened.
[INFO SPI Flash @19-03-01 11:58:06] Started download procedure...
[ACTION SPI Flash @19-03-01 11:58:07] Please press the hardware reset button on the board to start the download process.
[ERROR SPI Flash @19-03-01 11:58:22] Timeout: Reset signal not detected for more than 16000 msecs.
[INFO Booter @19-03-01 11:58:22] Successfully disconnected from port COM16.
[INFO Booter @19-03-01 11:58:22] Successfully disconnected from port COM16.
[ERROR SPI Flash @19-03-01 11:58:22] Failed downloading firmware file to the board.
[ERROR SPI Flash @19-03-01 11:58:22] Failed configuring SPI Flash ports and pins.
[INFO SPI Flash @19-03-01 11:58:30] Firmware File C:\DiaSemi\DA14585_SDK\6.0.10.511\config\toolbox_resources/common/flash_programmer.bin has been selected for downloading.
[INFO SPI Flash @19-03-01 11:58:30] Connection to COM16 port has successfully opened.
[INFO SPI Flash @19-03-01 11:58:30] Started download procedure...
[ACTION SPI Flash @19-03-01 11:58:31] Please press the hardware reset button on the board to start the download process.
[错误SPI Flash @ 19-03-01 11:58:46]超时：未检测到超过16000毫秒的重置信号。
[INFO Booter @19-03-01 11:58:46] Successfully disconnected from port COM16.
[ERROR SPI Flash @19-03-01 11:58:46] Failed downloading firmware file to the board.
[ERROR SPI Flash @19-03-01 11:58:46] Failed configuring SPI Flash ports and pins.
[INFO SPI Flash @19-03-01 12:08:13] Firmware File C:\DiaSemi\DA14585_SDK\6.0.10.511\config\toolbox_resources/common/flash_programmer.bin has been selected for downloading.
[INFO SPI Flash @19-03-01 12:08:13] Connection to COM16 port has successfully opened.
[信息SPI Flash @ 19-03-01 12:08:13]开始下载程序...
[ACTION SPI Flash @19-03-01 12:08:14] Please press the hardware reset button on the board to start the download process.
[ERROR SPI Flash @19-03-01 12:08:29] Timeout: Reset signal not detected for more than 16000 msecs.
>Also, are you able to connect/erase the SPI flash over JTAG or your only issue is that you can not burn it?
No, I cant to erase, but connection seems okay
Hi azimin,
In case you have a custom board, could you please try to download firmware into the SystemRAM through Keil IDE? The reason that I suggest you that is to make sure that your board is fully functional, so I would suggest you to use the ble_app_bearbone example of the SDK, compile it for DA14586 and the download the firmware into SysRAM? Are you able to detect your device from a BLE mobile application? Also you could use the power profiler of SmartSnnippets toolbox to make sure that your device is advertising.
Thanks, PM_Dialog
Yes, my board is working with Keil IDE and the code is running from RAM. I can see my device with mobile app
Hi azimin,
The most possible reason why you are not able to connect and burn the SPI flash is why you are not have a reset circuit to your custom board. The SPI flash configuration from the SmartSnippets toolbox are correct and according to DA14586 datasheet. In all reference designs we have a reset button, when trying to connect the user can reset the board in order to download the flas_programmer in case of UART or the jtag_programmer in case of jtag. The smart snippets does not support flash functionalities, so the SDK includes the flash programmer project which is under 6.0.10.511\utilities\flash_programmer. If you check there are 2 output on from uart and one from jtag. When you are connected to smart snippets and press reset, you download one of the two binaries. Let me ask you something. Which version of JTAG are you using?
Thanks, PM_Dialog
Hello,
Finally I made a board with reset circuit. I reset the chip and press connect button after.
In case of J-link I got this log:
[INFO SPI Flash @19-03-12 14:47:16] Found SW-DP with ID 0x0BB11477
[INFO SPI Flash @19-03-12 14:47:16] Using pre-configured AP[0] as AHB-AP to communicate with core
[INFO SPI Flash @19-03-12 14:47:16] AP-IDR: 0x04770021, Type: AHB-AP
[INFO SPI Flash @19-03-12 14:47:16] AHB-AP ROM: 0xE00FF000 (Base addr. of first ROM table)
[INFO SPI Flash @19-03-12 14:47:16] Found Cortex-M0 r0p0, Little endian.
[信息SPI Flash @ 19-03-12 14:47:16] FpUnit：4代码（BP）插槽和0个字幕插槽
[INFO SPI Flash @19-03-12 14:47:16] CoreSight components:
[INFO SPI Flash @19-03-12 14:47:16] ROMTbl[0] @ E00FF000
[INFO SPI Flash @19-03-12 14:47:16] ROMTbl[0][0]: E000E000, CID: B105E00D, PID: 000BB008 SCS
[INFO SPI Flash @19-03-12 14:47:16] ROMTbl[0][1]: E0001000, CID: B105E00D, PID: 000BB00A DWT
[INFO SPI Flash @19-03-12 14:47:16] ROMTbl[0][2]: E0002000, CID: B105E00D, PID: 000BB00B FPB
[INFO SPI Flash @19-03-12 14:47:16] Firmware File C:\DiaSemi\DA14585_SDK\6.0.10.511\config\toolbox_resources/common/jtag_programmer.bin has been selected for downloading.
[INFO SPI Flash @19-03-12 14:47:16] Successfully downloaded firmware file to the board.
[INFO SPI Flash @19-03-12 14:47:16] Successfully configured SPI Flash ports and pins.
[INFO SPI Flash @19-03-12 14:47:19] Started burning memory with 31016 bytes of data at address 0x00000.
[ERROR SPI Flash @19-03-12 14:47:29] Memory burning failed.
In case of UART I got this:
[INFO SPI Flash @19-03-12 14:44:25] Firmware File C:\DiaSemi\DA14585_SDK\6.0.10.511\config\toolbox_resources/common/flash_programmer.bin has been selected for downloading.
[INFO SPI Flash @19-03-12 14:44:26] Connection to COM16 port has successfully opened.
[INFO SPI Flash @19-03-12 14:44:26] Started download procedure...
(信息橄榄球员@19-03-12 14:44:27]成功盘onnected from port COM16.
[INFO SPI Flash @19-03-12 14:44:28] Connection to COM16 port has successfully opened.
[INFO Booter @19-03-12 14:44:28] Successfully disconnected from port COM16.
[INFO SPI Flash @19-03-12 14:44:28] Successfully downloaded firmware file to the board.
[信息SPI Flash @ 19-03-12 14:44:28]成功配置了SPI闪存端口和引脚。
[INFO SPI Flash @19-03-12 14:44:37] Started burning memory with 31016 bytes of data at address 0x00000.
[INFO SPI Flash @19-03-12 14:44:37] Connection to COM16 port has successfully opened.
[ERROR SPI Flash @19-03-12 14:44:53] Timeout while waiting to receive the most significant byte of packet length (10000 msecs)
[INFO Booter @19-03-12 14:44:53] Successfully disconnected from port COM16.
[ERROR SPI Flash @19-03-12 14:44:53] Memory burning failed.
Or this:
[INFO SPI Flash @19-03-12 15:26:28] Firmware File C:\DiaSemi\DA14585_SDK\6.0.10.511\config\toolbox_resources/common/flash_programmer.bin has been selected for downloading.
[INFO SPI Flash @19-03-12 15:26:29] Connection to COM16 port has successfully opened.
[INFO SPI Flash @19-03-12 15:26:29] Started download procedure...
[INFO Booter @19-03-12 15:26:30] Successfully disconnected from port COM16.
[INFO SPI Flash @19-03-12 15:26:31] Connection to COM16 port has successfully opened.
[INFO Booter @19-03-12 15:26:31] Successfully disconnected from port COM16.
[INFO SPI Flash @19-03-12 15:26:31] Successfully downloaded firmware file to the board.
[INFO SPI Flash @19-03-12 15:26:31] Successfully configured SPI Flash ports and pins.
[INFO SPI Flash @19-03-12 15:27:24] Started reading 32768 bytes from memory.
[INFO SPI Flash @19-03-12 15:27:24] Connection to COM16 port has successfully opened.
[INFO Booter @19-03-12 15:27:31] Successfully disconnected from port COM16.
[INFO SPI Flash @19-03-12 15:27:31] Reading has finished. Read 32768 bytes.
[INFO SPI Flash @19-03-12 15:27:35] Started burning memory with 31016 bytes of data at address 0x00000.
[INFO SPI Flash @19-03-12 15:27:35] Connection to COM16 port has successfully opened.
[ERROR SPI Flash @19-03-12 15:27:41] Received error message while checking whether burning was successful: FFFFFFF8.
[信息Booter @ 19-03-12 15:27:41]成功与COM16端口断开连接。
[ERROR SPI Flash @19-03-12 15:27:41] Memory burning failed.
I'm using J-Link V6.42c
With Keil runtime debugging the board works
Hi azimin,
If I understood correctly, you can connect from the flash programmer, but you are not able to burn the SPI flash? Which SPI flash are you using into your custom board? Also, is it empty? If not, are you able to erase it?
Thanks, PM_Dialog
Hello, I'm using internal flash memory. Finally I found the problem - I forgot to connect VCC_FLASH. No it works. Thank you for your efforts.
Hi azimin,
由于您没有连接的VCC_FLASH，您将无法访问内部SPI闪存。很高兴你识上你的问题。干杯!
Thanks, PM_Dialog