您好，我正在搜索所述的帖子和对话框：
"You dont need any extra cable or a Jtag since you have the interface board, the board has a debugger, you just plug in the USB cable turn it on and you should be able to step and run the IoT
跟基尔一起去，你不需要额外的东西。图中所示的接口是另一个接口，用于编程参考设计，并使用不同的Jtag连接插头。”
I have the interface board/IOT sensor combo. I have tried downloading the code through smart snippets but was not successful then I noticed this post. I would like to use the debugger
这里提到了这一点，但是当我启动keil并编译IOT项目并尝试打开调试器时，我得到了错误：没有找到Cortex-M设备。我的Keil可以使用DA14580开发工具包。有什么想法吗？非常感谢。克雷格
Device:
嗨，克雷格，
伴随着物联网传感器的接口板is the one indicated in the UM-B-063 sensor development kit documentation in figure 5. Please open keil and choose the options for target, go to the debug tab and click settings, there you should see the SN of the JTAG (make sure that the port is set to SW and not JTAG). The problem is, if the 583 has firmware inside the internal flash and the fw implements sleep, the JTAG wont be able to attach to your processor. So if you dont see under the SW Device text box your processor, hit the ok or cancel button to go back in the Debug tab, hit the reset on the the interface board and click again the settings options before the 583 goes to sleep, in order to make sure that keil is able to communicate with your processor. Now in order to program the via keil before hitting the debug button on keil, hit the reset button on the interface board and hit the debug button from keil within approximatelly 2 seconds. I remind you that the above are necessary because the fw implements sleep and the debugger can't attach to the 580. You can remove the fw that is programmed into the flash by using smart snippets and the connect via JTAG, hit the flash option, hit connect, and then erase, that way you dont have to hit the reset button every time you want to program your board.
谢谢你的对话
感谢您的详细回复。这将有助于一些将遇到这个问题的人。至于我，我现在的董事会仍然有问题，我不能用智能片段或通过Keil编程-我相信它是董事会本身，所以我从Mouser那里寄来了一个新的，如果
我在那块木板上遇到了任何问题。再次感谢。克雷格
你好，
在高频采样时，“物联网传感器开发套件-9轴+温度/压力/湿度”将绘制多少电流。
是任何有关当前/功耗详细信息的文档。
Regards,
玛赫钱德安娜。
Hi Mahesh,
You can find the power consumtion measurements in the UM-B-063_DA145_IoT_sensor_development_kit.pdf at section 12.1 Power measurements along with the rates of the sensors that the measurement is done. Those are the available measurements that have been performed on the IoT
谢谢你的对话
你好，我有麻烦了programming my new boards. The boards were just manufactured and have the same pinouts/pin connects for programming
(including the 10 pin header) as your DA14583 IOT board. I cannot program them using either UART/SPI mode or JTAG mode. My existing
来自对话框的物联网传感器在这两种模式下都可以正常工作。我想我真的需要支持，因为这些板很贵
他们是捏造的，似乎有硬件问题。以下错误是从智能代码段中获得的：我正在查找
一种在此时调试它们的策略。非常感谢。克雷格
JTAG模式：
[INFO @16-12-25 14:00:27] Header records have been removed from hex file wrbl_sfl_583.hex.
[INFO @16-12-25 14:00:27] Read 32688 bytes from file wrbl_sfl_583.hex.
[INFO@16-12-25 14:00:28]Core已锁定，试图禁用WDT。
[警告@16-12-25 14:00:29]无法设置S\u RESET
[警告@16-12-25 14:00:29]CPU复位后未停止。
[警告@16-12-25 14:00:29]CPU无法停止
[INFO @16-12-25 14:00:29] Core did not halt after reset, trying to disable WDT.
[警告@16-12-25 14:00:29]CPU复位后未停止。
[警告@16-12-25 14:00:29]CPU无法停止
[警告@16-12-25 14:00:29]无法设置S\u RESET
[INFO@16-12-25 14:00:29]SYSRESETREQ已混淆核心。正在尝试重新连接并使用向量集。
[WARNING @16-12-25 14:00:30] Failed to reset CPU. VECTRESET has confused core.
[警告@16-12-25 14:00:30]CPU复位后未停止。
[WARNING @16-12-25 14:00:30] CPU could not be halted
[INFO@16-12-25 14:00:30]复位后，Core未停止，试图禁用WDT。
[警告@16-12-25 14:00:30]CPU复位后未停止。
[WARNING @16-12-25 14:00:30] CPU could not be halted
[WARNING @16-12-25 14:00:30] Could not set S_RESET_ST
[ERROR @16-12-25 14:00:30] Failed writing value A7 at address 50000012.
[INFO @16-12-25 14:00:30] Failed downloading firmware file to the board.
[INFO @16-12-25 14:00:30] Failed configuring SPI Flash ports and pins.
UART/SPI Mode:
[INFO@16-12-25 14:55:30]已从十六进制文件wrbl\u sfl\u 583.hex中删除标头记录。
[INFO @16-12-25 14:55:30] Read 32688 bytes from file wrbl_sfl_583.hex.
[INFO@16-12-25 14:55:35]将固件文件下载到板失败。
[INFO @16-12-25 14:55:35] Failed configuring SPI Flash ports and pins.
[INFO@16-12-25 14:55:44]将固件文件下载到板失败。
[INFO @16-12-25 14:55:44] Failed configuring SPI Flash ports and pins.
[INFO @16-12-25 14:55:57] Failed downloading firmware file to the board.
[INFO@16-12-25 14:55:57]配置SPI闪存端口和引脚失败。
[INFO @16-12-25 14:56:13] Failed downloading firmware file to the board.
[INFO@16-12-25 14:56:13]配置SPI闪存端口和引脚失败。
[INFO @16-12-25 14:56:17] Failed downloading firmware file to the board.
[INFO @16-12-25 14:56:17] Failed configuring SPI Flash ports and pins.
[INFO@16-12-25 14:56:28]将固件文件下载到板失败。
[INFO@16-12-25 14:56:28]配置SPI闪存端口和引脚失败。
嗨，克雷格，
Regarding to the flash programming, please check the SPI flash pin configuration in Board Setup to match DA14583 pin assigement and use UART mode instead of UART/SPI mode when there is no function of current measurement. Smartsnippets usually ask users to press reset button in UART mode in order to download a flash_programmer.bin before programming a flash image, but I dont see it in the console you provided. So there might some incorrect steps in your setup. Please also confirm both of the UART and JLink driver are installed correctly.
Flash download is not supported in Keil. Please use "debug" and download the image to RAM.
Thanks Morris
谢谢你的帮助。我realized I am missing the central solder pad for the 40VFQFN processor. Routed
垫子下面有几条线。我想这就是问题所在。我看了一下数据表，没有多少
提到中央键盘，我不知道这是我第一次使用这个芯片
格式。
For the sake of my fix where I have to be a bit creative in dealing with the central ground pad, I need to know (and couldn't
find in the datasheet), if pin 16 (DA14583 GND pin 16) is connected internally to the central ground pad? If not, can I get away with not grounding
that central ground pad or is that an absolute necessity? Thank you in advance. Craig
嗨，克雷格，
引脚16是DCDC接地，未连接到作为中央接地垫的基板接地。因此，有必要进行接地垫连接。评估委员会的布局可以为您提供很好的参考。
Thanks Morris