Yes, there is a Battery Profile available for you to monitor the battery. Please refer to following documents to implement this into your application. However this profile gives you the information related to how much charge is left on the Battery.
RW-BLE-PRF-BAS-IS: This gives you the information about the APIs.
bass.handbasc.h: For implementation details
UM-B-050_DA1458x_Software_Developer's_Guide_1v1: Checkout the section 6.6 on how to add the profile.
Note:This is a very simple step. You would just need to add the header file of the specific profile to the user_profiles_config.h
For your second question...
In order to look at the current readings for different events, the SmartSnippets Power Profiler is the best choice. This is supplied along with the SDK or you can download from the support portal. Using this tool is simple and straight forward. However, you would need to have a DA14580_PRO_DevKit and you can connect the IOT DevKit to this Pro DevKit to do the power profiling which is also a simple and easy step.
Q1 : I am using MUARATA P2ML 3656 LBCA2HnZYZ Dev board (DA14580) , also IOT Smart Band Dev kit - DA14583 , can i use power profiler with these boards. Also please mention how to use the power profiler with these boards.
Q2:如何使用DMM with these kits to measure the current drawn from Source, Please mention with connection diagram
If i want to use the Oscilloscope with the MUARATA P2ML 3656 LBCA2HnZYZ Dev board (DA14580) dev kit , which TESTPOINTS i have to use ??? also mention for DMM also
A1 : Yes, you can use the power profiler using the MURATA P2ML 3656 DevKit. The IOT SmartBond does not support the profiling. But you can use the MURATA DevKit to route the input source to the IOT DevKit to use the power profiler. Please look at the schematics of the DevKits to understand how to connet the DevKits.
A2 : In order to measure the current connect your DMM test leads between the input source jumpers if the DevKit provide such jumpers. Regarding the exact pin configuration, you might have to look at the schematics or approach Murata for additional support in the context of DevKit. It is the same for the Oscilloscope measurements on Murata DevKit.
For the IOT DevKit Current Measurements, there is a jumper J16. You can connect your DMM test leads to the pins of this jumper and you can get the current readings.
I want to power MURATA P2ML 3656 LBCA2HnZYZ Dev board (DA14580) with cr2032 coin cell battery , can u tell corresponding Jumber settings in the DEV board.
Unfortunately, I do not have access to the MURATA board now. Please reach out to the MURATA support regarding the MURATA P2ML 3656 DevKit. I would be happy to help regarding Dialog DevKits as I have access to these.
Hi dialog
want to measure the current drawnfrom battery during advertising , connection , wake up , data tx all cases ...thank you
Hello Prasanth,
For your first question...
Yes, there is a Battery Profile available for you to monitor the battery. Please refer to following documents to implement this into your application. However this profile gives you the information related to how much charge is left on the Battery.
RW-BLE-PRF-BAS-IS: This gives you the information about the APIs.
bass.handbasc.h: For implementation details
UM-B-050_DA1458x_Software_Developer's_Guide_1v1: Checkout the section 6.6 on how to add the profile.
Note:This is a very simple step. You would just need to add the header file of the specific profile to the user_profiles_config.h
For your second question...
In order to look at the current readings for different events, the SmartSnippets Power Profiler is the best choice. This is supplied along with the SDK or you can download from the support portal. Using this tool is simple and straight forward. However, you would need to have a DA14580_PRO_DevKit and you can connect the IOT DevKit to this Pro DevKit to do the power profiling which is also a simple and easy step.
Best,
LC
Hi Dialog
Thank you for your reply , i have Muarata dev board and IOT smart band dev board can i use this boards in Smart snippets power profile ??
Thank you Dialog...
Hello Prasanth,
Can you please specify which type of Murata DevKit you have?
Best,
LC
Hi Dialog
Q1 : I am using MUARATA P2ML 3656 LBCA2HnZYZ Dev board (DA14580) , also IOT Smart Band Dev kit - DA14583 , can i use power profiler with these boards. Also please mention how to use the power profiler with these boards.
Q2:如何使用DMM with these kits to measure the current drawn from Source, Please mention with connection diagram
Thank you Dialog
Hi Diaolog
If i want to use the Oscilloscope with the MUARATA P2ML 3656 LBCA2HnZYZ Dev board (DA14580) dev kit , which TESTPOINTS i have to use ??? also mention for DMM also
Thank you dialog
Hello Prasanth,
A1 : Yes, you can use the power profiler using the MURATA P2ML 3656 DevKit. The IOT SmartBond does not support the profiling. But you can use the MURATA DevKit to route the input source to the IOT DevKit to use the power profiler. Please look at the schematics of the DevKits to understand how to connet the DevKits.
A2 : In order to measure the current connect your DMM test leads between the input source jumpers if the DevKit provide such jumpers. Regarding the exact pin configuration, you might have to look at the schematics or approach Murata for additional support in the context of DevKit. It is the same for the Oscilloscope measurements on Murata DevKit.
For the IOT DevKit Current Measurements, there is a jumper J16. You can connect your DMM test leads to the pins of this jumper and you can get the current readings.
Best,
LC
Hi Dialog
Thank you for your answer.
I want to power MURATA P2ML 3656 LBCA2HnZYZ Dev board (DA14580) with cr2032 coin cell battery , can u tell corresponding Jumber settings in the DEV board.
Hello Prasanth,
Unfortunately, I do not have access to the MURATA board now. Please reach out to the MURATA support regarding the MURATA P2ML 3656 DevKit. I would be happy to help regarding Dialog DevKits as I have access to these.
Best,
LC